Do-it-yourself patch panels

raustin |

Fabricating patch panels made simple

The outer quarter panel Leonard Schrock is fabricating will fit the passenger side. Here, the old, rusty metal has already been removed after the car was sandblasted.

 

By Angelo Van Bogart

Even on the West Coast and in Texas, it’s getting more difficult to find a 30-year-old or older project car without a case of the tin worm. Chances are, a project car is going to require some metal replacement, and when that metal isn’t available from a reproduction part producer or a parts car, there is but one alternative — make the part yourself.

The subject car here is one of those cars for which limited replacement sheet metal is available. Reproduction companies haven’t quite caught up to the subject project car, a 1973 Plymouth Road Runner, and there is only a limited amount of new metal available. To bring back this tin worm-infested ’Runner back to show condition, master metal man Leonard Schrock is prepared to cut and bend plain flat-stock sheet metal  into the curves of the 1973.

In this case, he’ll be replacing the quarter panel around the rear wheel opening on the ’Runner. For this task, Schrock cut two separate panels — one for the inner fender lip and another for the outer quarter panel — from sheet metal stock and welded them together. Using two separate pieces and welding together will make the piece stronger and also make it easier to shape the metal than making the piece out of one piece of metal.

 

Bad Dust

BAD Dust® Containment Systems

Reusable, modular containment bags designed to shield airborn dust and friable materials created by treating surfaces with media-blasting equipment or other mechanically operated hand held tools. www.baddust.com

APS

Auto Paint Specialists

Tower Paint™. APS/Tower Paint
The Original Custom
Color Spray Can Leader
2120 West Nordale Drive
Appleton, WI. 54914
1-800-529-0579
www.apstowerpaint.com

C&G Early Ford Parts

C&G Early Ford Parts

C&G Early Ford Parts for 1932-1979 Ford car and Ford truck parts! Service, selection, knowledge, and quality. Come experience what folks who have old cars can do for you. www.cgfordparts.com

CWG

Continental Western Group

It’s all about value! No matter if you’re talking about Agreed Value
coverage for your vehicles, or superior insurance value, we provide both! We hold an “A+, Superior” financial strength rating, which few can match! www.cwgcollectorcar.com

 

An oversized piece of flat stock is placed against the body so Leonard Schrock can trace the shape of the wheel opening and cut the metal to shape. The trace line is very faint.

To begin, the profile and body lines of the rusted outer quarter panel that will be replaced must be recorded with templates. Three thin pieces of metal were formed to the shape and contours of the quarter panel around the Road Runner’s wheel opening and their locations on the car marked. Since there are multiple contours to the wheel opening (top, front and rear of wheel opening), all of their shapes must be recorded with separate strips of tin and marked for their position on the fender.

The overall shape of the wheel opening must also be marked. Schrock placed the flat sheet metal stock he will use to form the replacement panel against the wheel opening on the car and traced its shape on the new sheet metal. Schrock had already cut out the rust from this area, so he used the inner fender as a guide, because these two panels (inner and outer quarter panel) must meet and be welded together.

Once the shape of the wheel opening is traced on the oversized flat piece of stock, Schrock highlights his cut line with painter tape and uses a power shears to cut the metal.

 

Schrock highlights the cut line with a piece of 3/4-inch tape to guide his power shears.

The lower line marks the wheel opening and where the metal will be cut with power shears. This line is outlined here with tape.

 

LoJack for Classics

Classic cars are stolen every day. Get yours back with LoJack for Classics. Providing a 90% success rate in tracking and recovering stolen cars and trucks, LoJack now offers a stolen vehicle recovery system designed specifically for your one-of-a-kind pride and joy. Visit www.lojackforclassics.com, use promo code CCEML295 to save $400.

Bad Dust

Qual Krom

For the past 24 years Qual Krom has been meeting the needs of their customers by providing chrome restoration service second to none. Count on us for your next chrome refinishing project!
www.qualkrom.com

JC Auto

JC Auto Restoration

JC Auto has been in business for 34 years restoring a variety of vintage automobile components. We have an extensive inventory, specialing in hard-to-find parts for Chrysler products. www.jcauto.com

Steele Rubber

Steele Rubber

Protect your vehicle with quality rubber parts. Don’t forget to check the quality of your original rubber seals. Over time, weatherstripping and rubber parts can degrade. Steele Rubber offers a complete line of quality rubber parts for American-made vehicles from the 1920′s-1990′s.
Visit us online

 

The power shears Schrock employed to cut the flat sheet metal stock.

Next, Schrock prepared to cut the metal that will form the lip inside the wheel opening. He repeated the previous step, placing a piece of flat stock in the wheel opening to trace the shape of the lip. Tape was placed on the drawn line and he cut the metal to shape. The width of the lip was originally 1-1/4 inch, but the owner will be running wider tires, so Schrock cut the lip to 3/4 inch wide, the minimum width Schrock suggests to maintain strength in this part of the car.

This metal strip forming the lip inside the wheel opening bends around the tire, from in front of the wheel opening to above the tire to the back of the fender. As such, it must be bent, so Schrock begins bending the cut piece of metal at its end to avoid kinks. He works the strip over his knee to the center of the strip to avoid kinking the piece. He frequently compares its shape to the outer quarter panel it will meet until he is satisfied with the shape.

 

 

 

Midwest Power Products, Inc.

We specialize in rebuilding treadle-vac, master-vac and hydrovac power brake boosters for classic cars and trucks. In addition, military, agricultural and industrial applications. We also offer .304 stainless steel sleeving service, rebuilding kits and a full line of new brake components.
midwestbooster.com

CUSTOM PLATING SPECIALIST

We specialize in restoration, show quality plating and salvaging damaged chrome parts that other platers have ruined.
We can plate nearly any material. We can remove dents & scratches and polish any item.
email: tmeetz@aol.com
www.customplatingspecialist.com

Northwestern Auto Supply

An old time parts store since 1946 with 4 buildings full of old inventory of antique and classic parts for the quality minded owner who wants to avoid off shore products. Engine, chassis, ignition, and brake parts shipped world wide. Machine shop and babbiting also. www.northwesternautosupply.com

RestoreATag

RestoreATag, the premier tag restoration company, uses a unique process that makes even the ugliest, rustiest tag a beauty to behold. Regardless of your state, we can restore an existing tag or create a vanity tag just for you. The options are endless! restoreatag.com

 

Schrock cuts the sheet metal with the power shears.

The remaining patch panel after the excess metal was removed.

With the two pieces cut to shape, Schrock was ready to begin pounding the contours around the wheel opening into the outer quarter panel. Schrock secured thick bar stock with clamps at the edge of the new panel where he’ll be forming the contours. It will allow him to bend the metal at sharper angles using a duckbill pliers. (For smoother bends, it is not necessary to support the metal with a bar stock guide.) The thick bar stock will act as a guide to where he’ll be bending and shaping the contours, but also braces the surrounding metal so it, too, does not bend until he’s ready to address it.

At this point, he estimates the shape of the contours around the wheel opening, frequently comparing it to the thin metal templates he formed earlier from the body line.

 

These templates outlined the shape of the original outer rear quarter panel. Schrock will use these to guide his forming of the new outer rear quarter panel. Note each template is marked with its location.

 

 

soundmove.com
Restoring a classic car or truck? Compliment your restoration with a classic look radio that fits and blends right in. Our radios have the appearance of the factory original but with today’s electronics. www.soundmove.com
Tee-Bird Tee-Bird Products, Inc.
Stocks a large selection of quality parts for 1955-1956-1957 Thunderbirds and 1955-1956 Ford. Prompt shipping and knowledgeable service since 1973. Call 610-363-1725 or visit our website.
Vintage Thunderbird Club International
Vintage Thunderbird Club International is the largest ALL Thunderbird Club in the world! You can find us at www.vintagethunderbirdclub.net. Stop by and check us out, you can join the club on our website, we also have a very informative forum for all your Thunderbird questions. Get the “VTCI Experience!”
ClampTite
The CLAMPTITE TOOL provides a means of tightening wires wrapped around an object and then locking it in place. The tool can be used with various wire sizes which eliminates space and strength issues often encountered with screw operated worm gear type clamps. 1-800-962-2901 www.clamptitetools.com

 

A second, oversized piece of sheet metal stock is placed in the rear fender well to size up the new wheelwell lip. Schrock butts the new metal against the existing inner quarter panel to guide the line he will cut to form the lip inside the rear quarter panel.

To pound the template shape into the outer quarter panel, Schrock uses a body hammer with a convex face to further shape the metal. The convex-faced body hammer also helps keep the sharp bends in the quarter panel, all the while leveling out the panel for a smooth surface.

Once the new outer quarter panel is shaped with the original fender’s contours, Schrock lined up the new lip against the shaped outer quarter panel. Some bending was required, so he bent the new outer quarter panel by hand to match the lip piece he created. Once the pieces were lined up in the ideal location, Schrock drew a line across both pieces to mark the proper place to tack weld them together with a wire-feed welder.

Schrock used a power shears to cut the sheet metal that will form the lip (top metal sheet). Since the lip will be 3/4 inches wide, a piece of tape matching that width was run along the edge of his cut and then the metal was again cut along the opposite edge of the tape strip.

The lip is held into place.

 

 

Automotive Wiring and Electrical Systems is an enthusiast’s guide that takes the mysteries out of automotive electrical diagnostics and repair.

Click here to learn more

In Automotive Bodywork and Rust Repair, Matt Joseph shows you how to tackle both simple and difficult rust and metalwork projects.

Click here to learn more

 

Welding the two pieces together can be tricky at the lower part of the fender, due to the size and contours of the metal. Schrock slowly tack welded from the top to the bottom of the fender, bending and hammering the outer quarter panel to match the lip as he worked down from the top of his  new patch panel.

His tack welds were widely spaced and were intended to simply hold the pieces together until they would be completed wire-feed welded  together. The weld was then grinded smooth, and the new panel was ready to be mounted on the car.

More images of the process:

The quarter panel around the wheel opening is highly sculpted on a 1971-’74 Road Runner, so Schrock must bend and hammer the new panel to the original shape. A piece of thick flat metal stock is placed along the edge Schrock will begin bending the metal to form the sculpted bends. The thick bar metal stock works well for make sharp bends, but softer bends do not require it.

A second duckbill pliers is used to bend the inner edge of the new quarter panel patch piece.

Schrock measured the width of metal he’ll need to bend, marked that width on the new fender and bent the metal by eye, frequently checking his progress against the template.

Schrock used a convex body hammer to finish off the edge of the outer quarter panel after initially using the duckbill pliers.

 

Schrock lines up the two metal pieces he fabricated — the outer quarter panel patch and the lip inside the wheelwell — and determines where they should be welded together. Once they’re in the ideal position, he draws a line from one panel to the other, indicating where they should be tack welded in place.

The two panels are tack welded together.

Now that the pieces are tack welded together, their seam can be fully welded and the weld then ground smooth.

The new piece is ready to be installed on the quarter panel.

 

Source:
Kasper Automotive
Waupaca, Wis.
715-258-9206
www.kasperautomotive.net

 

 

 

If you liked this article on fabricating patch panels, you might be interested in:

More Resources For Car Collectors:

 

Leave a Reply