Fending for yourself: Attaching fender skirts

raustin |

Resto how-to: Putting fender skirts back on a Pontiac 2+2

When no fender skirts are installed, this car uses chrome wheel lip trim with painted metal under it.

By John Gunnell

Fender skirts are a fad that comes and goes. When vehicle documentation shows that a car had fender skirts when it left the factory, some owners want them reinstalled, regardless of the current fashion. This usually requires a lot more work than it did to glue fender skirts to the model car they built as a kid.

Fender skirts require rubber seals along the upper edge to help keep road debris from seeping through the joint where a skirt meets the wheel well. There are usually clips at each lower corner that support the panel in place on the car. A rotating or cam-type latch mechanism is required. It must allow fitting the skirt loosely in place, then tightening the fit so it stays in place. Some latching systems have a rather elaborate linkage. Fender skirts may also have bright metal trim, emblems or badges, and most must be painted to match the car.

 

Bad Dust

BAD Dust® Containment Systems

Reusable, modular containment bags designed to shield airborn dust and friable materials created by treating surfaces with media-blasting equipment or other mechanically operated hand held tools. www.baddust.com

APS

Auto Paint Specialists

Tower Paint™. APS/Tower Paint
The Original Custom
Color Spray Can Leader
2120 West Nordale Drive
Appleton, WI. 54914
1-800-529-0579
www.apstowerpaint.com

C&G Early Ford Parts

C&G Early Ford Parts

C&G Early Ford Parts for 1932-1979 Ford car and Ford truck parts! Service, selection, knowledge, and quality. Come experience what folks who have old cars can do for you. www.cgfordparts.com

CWG

Continental Western Group

It’s all about value! No matter if you’re talking about Agreed Value
coverage for your vehicles, or superior insurance value, we provide both! We hold an “A+, Superior” financial strength rating, which few can match! www.cwgcollectorcar.com

 

A rubber gasket on the skirt is required to seal it against the wheel opening. On a Pontiac such as this 1966, the wheel opening trim will be removed and the NOS skirts will be drilled for bright metal moldings that continue the body line.

Vintage fender skirts are available from many hobby vendors and, in a few cases, from reproduction sources. Locating a pair of skirts can be tricky. We have seen some that are aftermarket items being sold as originals. Used fender skirts can also be pretty rough and rusty. Some cars were never available from the factory with fender skirts (e.g., 1955-’57 Chevrolets). If authenticity is your angle, check factory sales literature to make sure you car was available with factory skirts and to verify what they looked like before buying a pair.

In everyday use, fender skirts took a real beating. Rocks could fly up and dent them on the outside. Road silt collected on the back side, which stored moisture and corroded the metal skirt. Fender skirts also flew off, were run over and even became scraped against tight garage door openings. The delicate trim on some skirts was easy to ding or scrape in the normal removal and installation procedure to change a flat tire. Ditto for the paint finish on the skirt.

 

 

LoJack for Classics

Classic cars are stolen every day. Get yours back with LoJack for Classics. Providing a 90% success rate in tracking and recovering stolen cars and trucks, LoJack now offers a stolen vehicle recovery system designed specifically for your one-of-a-kind pride and joy. Visit www.lojackforclassics.com, use promo code CCEML295 to save $400.

Bad Dust

Qual Krom

For the past 24 years Qual Krom has been meeting the needs of their customers by providing chrome restoration service second to none. Count on us for your next chrome refinishing project!
www.qualkrom.com

JC Auto

JC Auto Restoration

JC Auto has been in business for 34 years restoring a variety of vintage automobile components. We have an extensive inventory, specialing in hard-to-find parts for Chrysler products. www.jcauto.com

Steele Rubber

Steele Rubber

Protect your vehicle with quality rubber parts. Don’t forget to check the quality of your original rubber seals. Over time, weatherstripping and rubber parts can degrade. Steele Rubber offers a complete line of quality rubber parts for American-made vehicles from the 1920′s-1990′s.
Visit us online

 

A set of four clips or brackets (two per side) were used by the factory to attach the fender skirts to the rear wheel openings. This nice, cleaned-up original set was $50.

Used skirts sell for a wide range of prices, but the trend is that they are getting pricier. A common skirt for a ’70s car can cost as little as $10. A large skirt for a 1941 Cadillac with chrome trim and emblems can cost thousands. Condition counts, too. This pair of New Old Stock (NOS) skirts for the subject 1966 Pontiac were $400. They did not come with attaching hardware or chrome trim. The factory finished them in black primer, so they had to be painted. They did include a nice, supple rubber gasket and the latching mechanism.

Plenty had to be done to the fender skirts before installing them. We purchased a second pair of used skirts for $100 to obtain the trim that mounts to the fender skirt. The used trim had to be carefully removed without ruining the fasteners (a two-hour job) so that it could be buffed and polished. A few of the studs that slide on the back of the trim strips and pass through the skirts were rusty and required replacing. We also had to make little rubber squares for the fastening system. They keep the Timmerman nuts on the back from turning.

These skirts came off a Grand Prix, but according to the Pontiac Master Parts Catalog, they fit all full-sized models. Research through literature or a club to come up with such facts can save money.

This is how the exterior surface of the used fender skirt looked before the bright trim was removed. Not bad, but check the later photos and keep this in mind when you’re shopping for fender skirts.

 

 

Midwest Power Products, Inc.

We specialize in rebuilding treadle-vac, master-vac and hydrovac power brake boosters for classic cars and trucks. In addition, military, agricultural and industrial applications. We also offer .304 stainless steel sleeving service, rebuilding kits and a full line of new brake components.
midwestbooster.com

CUSTOM PLATING SPECIALIST

We specialize in restoration, show quality plating and salvaging damaged chrome parts that other platers have ruined.
We can plate nearly any material. We can remove dents & scratches and polish any item.
email: tmeetz@aol.com
www.customplatingspecialist.com

Northwestern Auto Supply

An old time parts store since 1946 with 4 buildings full of old inventory of antique and classic parts for the quality minded owner who wants to avoid off shore products. Engine, chassis, ignition, and brake parts shipped world wide. Machine shop and babbiting also. www.northwesternautosupply.com

RestoreATag

RestoreATag, the premier tag restoration company, uses a unique process that makes even the ugliest, rustiest tag a beauty to behold. Regardless of your state, we can restore an existing tag or create a vanity tag just for you. The options are endless! restoreatag.com

 

The bright trim is held on the skirts by studs and Timmerman nuts. Little rubber squares are used under the tin nuts to keep them from turning loose. Liquid Wrench penetrating oil on the threaded studs prevents breaking them.

The penetrating oil eats rust away and, to a degree, holds down the amount of heat generated by a wrench. It is often this heat that causes rusty studs to break. New studs are probably available, but why take a chance?

At each corner, the bright metal trim was crimped over the fender skirt. These crimps had to be gingerly undone with a long, thin screwdriver and a tiny jeweler’s hammer. After the trim moldings were buffed and polished to new condition, the ends had to be re-crimped without scratching or marring the bright metal.

Even though the NOS skirts had nice rubber gaskets, they were removed for a quality paint job. The rubber gaskets were re-installed using a special upholstery stapler and stainless-steel staples.

After checking factory sales catalogs, we verified the bright metal trim around the rear wheel openings was not used on fender skirt-equipped cars.

Before we could get a 3/8-inch six-point socket on the Timmerman nuts, we had to remove all the crud. A hooked dental pick did a good job of removing crud from the tiny rubber pad shown here, which is used at the base of the stud.

We used a cheap wire brush to clean the threads on the studs. The cleaner the studs are, the easier the nuts will come off without generating heat and snapping a stud.

 

 

soundmove.com
Restoring a classic car or truck? Compliment your restoration with a classic look radio that fits and blends right in. Our radios have the appearance of the factory original but with today’s electronics. www.soundmove.com
Tee-Bird Tee-Bird Products, Inc.
Stocks a large selection of quality parts for 1955-1956-1957 Thunderbirds and 1955-1956 Ford. Prompt shipping and knowledgeable service since 1973. Call 610-363-1725 or visit our website.
Vintage Thunderbird Club International
Vintage Thunderbird Club International is the largest ALL Thunderbird Club in the world! You can find us at www.vintagethunderbirdclub.net. Stop by and check us out, you can join the club on our website, we also have a very informative forum for all your Thunderbird questions. Get the “VTCI Experience!”
ClampTite
The CLAMPTITE TOOL provides a means of tightening wires wrapped around an object and then locking it in place. The tool can be used with various wire sizes which eliminates space and strength issues often encountered with screw operated worm gear type clamps. 1-800-962-2901 www.clamptitetools.com

The edges of the bright trim were crimped over the ends of the fender skirt and had to be carefully un-crimped. These parts look very rusty, but what you’re actually seeing is road crud.

Since the restored car has these moldings in place, it will be necessary to remove them. Normally this would require repainting at least part of the rear fenders, but the owner wants to repaint his Pontiac and will spray the fender opening at that time.

The only thing left to deal with is the set of clips that were used to hold the fender skirts to the car. For this make and model, relatively simple, flat pieces of metal were used, and a good body shop could easily fabricate substitutes if good used parts cannot be located. We found a very nice set of media-blasted OEM clips for sale in an online auction for about $50.

The fronts of the bright trim moldings have minor deterioration. They will be buffed and polished to look new. This will be farmed out to Mike Freund of Classics Plus Ltd. (www.classicsplusltd.com) in Fond du Lac, Wis.

Clips with studs slide onto the back of trim and are likely available from Restoration Specialties (www.restorationspecialties.com) in Pennsylvania. The backs will also need some cleaning up.

 

 

Automotive Wiring and Electrical Systems is an enthusiast’s guide that takes the mysteries out of automotive electrical diagnostics and repair.

Click here to learn more

In Automotive Bodywork and Rust Repair, Matt Joseph shows you how to tackle both simple and difficult rust and metalwork projects.

Click here to learn more

 

Here’s how the used skirt looked like under the bright metal trim moldings. These are actually very solid compared to some.

The total cost of re-installing fender skirts on this car — from buying the NOS skirts, used skirts and hardware, plus buffing the trim and painting the skirts — will easily run close to $1,000.

On other cars, the cost could be lower or higher, depending on part prices, the amount and style of trim and the fender skirt attaching system. In all cases, it’s a lot more work to add fender skirts to a classic car now than it was to glue fender skirts on the model car you built as a kid.

The top row shows the rubber squares that keep the Timmerman nuts on the back of fender skirts (lower row) from turning after they are tightened. The nuts can be cleaned up with a wire wheel or replaced, but new rubbers will have to be made.

 

 

If you liked this restoration article on attaching fender skirts, you might be interested in:

More Resources For Car Collectors:

 

2 Responses to Fending for yourself: Attaching fender skirts

  1. Klaus Koenig says:

    Nice article!

    Do these skirts make my track look wider? No dear, they look great!

    My dad bought a decade old ’55 Chevy with skirts, the installation was much simpler… a piece of wood across the wheel opening and fiberglass draped down from the quarter panel. The only way to remove the wheel was to jack up the car from the side, even lifting from the back corner didn’t tilt the axle enough. And wider tires?… forget about it!

  2. Harold Davis says:

    Enjoyed the article. Fortunately, the skirts on my ’65 Chrysler 300 are only lightly rusted. The article has some excellent guides to restore them back to near new. Enjoy all of your articles on restoration.

Leave a Reply